G3HSPA00 – Cellular Modem Option Card – Red Lion Controls

$471.49

Supports HSPA+ cellular data connectivity with fall back to 3g and 2g

Part #: G3HSPA00

SKU: G3HSPA00 Category:

Description

G3HSPA00 Product Manual

POWER REQUIREMENTS:
24VDC ± 20%; (independent from the host G3 power connection). Must use
NEC Class 2 or Limited Power Source (LPS) rated power supply.
G3HSPA Max Power:
HSPA+ Mode: During continuous active webserver traffic
Instantaneous maximum: 5.5 W
Average: 3.7 W
GPRS Mode:
Instantaneous maximum: 14.5 W (1.1 msec every 4.6 msec)
Average: 7.0 W

LINK STATUS LEDs:
Link Status – Link Status LED shows cellular link condition.

COMMUNICATIONS:
Isolation from G3HSPA Antenna connector to G3 operator interface:
500 VDC for 1 minute.

ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: 0 to 50 °C
Storage Temperature Range: -20 to 80 °C
Operating and Storage Humidity: 80% maximum relative humidity (noncondensing)
from 0 to 50 °C.
Altitude: Up to 2000 meters.

ANTENNA CONNECTOR:
SMA Female connector requires:
50 Ohm antenna with SMA male connector
Penta-band HSPA+ antenna (850/900/1700/1900/2100 MHz) for global support.
Dual-band (850/1900 MHz) antenna for US and Canada only
Dual band (900/2100 MHz) for Europe only
Voltage Standing Wave Ratio (VSWR) should not exceed 2.0:1
The antenna cable should be 50Ω impedance, RG178/U or RG174/U type and be able to connect to the RSMA (Male) jack bulkhead. The antenna could be horizontal, vertical or right angled. Longer antenna cable would equate to signal loss.

CONSTRUCTION: Installation Category I, Pollution Degree 2

INSTALLATION REQUIREMENTS: Card must be installed inside the rear cover of a G3 operator interface with the hardware provided. See “Installing the G3HSPA Option Card” for more details.

WEIGHT: 2.5 oz (70.9 g)

GENERAL DESCRIPTION

The G3HSPA00 option card allows the user to add HSPA+ cellular modem capability to their G3 operator interface terminal. The cellular standard adopted in this option card is HSPA+ with fallback capability to 3G and 2G. It can get
speeds up to 21 Mbps downlink and 5.76 Mbps uplink. It’s built upon the GSM standard, offered in the US and widely available throughout the world. HSPA+ can be used for services such as Wireless Application Protocol (WAP) access, Short Message Service (SMS), and for Internet connectivity.

The G3HSPA00 option card is penta-band, allowing it to work in frequencies across the Americas, Europe and Asia. US and Canada work in the 850/1900 MHz bands, while Europe, Middle East, Africa and most of Asia work in the
900/1700/2100 MHz HSPA+ frequencies.

The G3HSPA requires the addition of a SIM (Subscriber Identity Module) card, which is inserted into the holder prior to installation of the G3HSPA card. The SIM card securely stores the service-subscriber key (IMSI) used to identify a subscriber, and is used to connect to the network to obtain an IP address from the provider.

  • Configured using Crimson® software (version 3.0 or later)
  • Supports HSPA+ cellular data connectivity with fall back to 3g and 2g
  • Up to 21 Mbps downlink/5.76 Mbps uplink speeds
  • Installs inside a G3 operator interface terminal
  • Installation and connection hardware included with card

Additional information

Weight 1 lbs

Documentation

G3HSPA Product Manual