Description
G09C0000 Product Manual
Manufacturer: Red Lion Controls
Product: HMI
Series: Graphite
Power: 10 to 30 VDC
Display Size: 9 inch
Resolution: WVGA Color Widescreen touchscreen (800 x 480)
Dimensions: 10.06″ x 6.47″ x 2.06″ (255.6 mm x 154.4 mm x 52.4 mm)
Indoor/Outdoor: Indoor
Serial Ports: 3
Ethernet Ports: One 10/100 Base-TX Ethernet Port
Module Slots: 6
Memory: 256 Mbyte of non-volatile Flash memory.
Battery: Lithium coin cell. Typical lifetime of 6 years, nominal.
Construction: Cast aluminum enclosure with NEMA 4X/IP66 rating when correctly fitted with the gasket provided.
Weight: 3.39 lb. (1.54 Kg)
Software: Free Crimson 3 Software
Free Shipping: Free UPS Ground Shipping
Red Lion G09C0000 advanced operator panels are the industry’s first rugged HMI touchscreens to combine a wide range of versatile plug-in modules with protocol conversion, data logging and web-based monitoring and control. With all cast-aluminum construction and hazardous approvals, Graphite HMIs support wide operating temperatures and high shock/vibration tolerances to enable you to connect, monitor and control processes regardless of environment.
- 9 inch WVGA Color Widescreen touchscreen (800 x 480)
- Indoor Model
- Up to 20 Simultaneous Protocol Conversions
- One 10/100 Base-TX Ethernet Port
- Three Fully Isolated Serial Communication Ports, (two RS-232 and one RS-422/485)
- One USB Type B Port
- Two High-retention USB Host Ports
- 6 Module Slots to Easily add I/O Capability with Plug-in Modules
- 256 x 164 mm Dimensions
Specifications
POWER REQUIREMENTS: 10-30 VDC
Must use a Class 2 circuit according to National Electrical Code (NEC), NFPA-70 or Canadian Electrical Code (CEC), Part I, C22.1 or a Limited Power Supply (LPS) according to IEC/EN 60950-1 or Limited-energy circuit according to IEC/EN 61010-1. Power connection via removable three position terminal block.
BATTERY: Lithium coin cell. Typical lifetime of 6 years, nominal.
LCD DISPLAY: 9 inch WVGA Color Widescreen touchscreen (800 x 480)
TOUCHSCREEN: Resistive analog
MEMORY:
On Board User Memory: 256 Mbyte of non-volatile Flash memory.
Memory Card: SD slot accepts standard capacity cards up to 2Gbyte
COMMUNICATION CAPABILITIES:
- USB Device Port: Adheres to USB specification 2.0 (high speed, full speed) only using Type B connection. USB DEVICE PORT IS FOR SYSTEM SET-UP AND DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT CONNECTION.
- USB Host Ports: Comply with Universal Serial Bus Specification Rev 2.0. Support data transfers at (high speed, full speed). Hardware over current protected (0.5 A max per port).
Serial Ports: Ports are individually isolated. Format and Baud Rates for
each port are individually software programmable up to 115,200
baud.
PGM Port: RS232 port via RJ12.
COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12.
DH485 TXEN: Transmit enable; open collector, VOH = 15 VDC,
VOL = 0.5 V @ 25 mA max.
Port to Port Isolation: 1000 Vrms (G07: 500 Vrms) for 1 minute.
Signal Isolation: 50 V.
- Ethernet Port: 10 BASE-T / 100 BASE-TX
RJ45 jack is wired as a NIC (Network Interface Card).
Isolation from Ethernet network to Graphite operator interface: 1500
Vrms
ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: -20 to 60 °C, or lowest range among
equipment used in your Graphite system.
Storage Temperature Range: -20 to 70 °C
Vibration to IEC 68-2-6: Operational 5-500 Hz, 4 g
Shock to IEC 68-2-27: Operational 40 g (10 g, modules w/relays)
Operating and Storage Humidity: 0 to 85% max. RH non-condensing
Altitude: Up to 2000 meters
Installation Category II, Pollution Degree 2 as defined in IEC/EN 60664-1.
CONNECTIONS: High compression cage-clamp terminal block
Wire Strip Length: 0.3″ (7.5 mm)
Wire Gauge Capacity: One 14 AWG (1.63 mm) solid, two 18 AWG (1.02 mm) or four 20 AWG (0.81 mm)
CONSTRUCTION: Cast aluminum enclosure with NEMA 4X/IP66 rating when correctly fitted with the gasket provided. These devices have only been evaluated for low risk of mechanical impact.
MOUNTING REQUIREMENTS: Maximum panel thickness is 0.188″ (4.78 mm) with removable foot, or 0.375″ (9.53 mm) without foot. For NEMA 4X/IP66 sealing, a steel panel with a minimum thickness of 0.125″ (3.17 mm) is recommended. Maximum Mounting Screw Torque: 6.0 lbf inch (96 ozf inch) (0.68 Nm)
WEIGHT: 3.39 lb. (1.54 Kg)
